Subaru Impreza GC8 & RS Forum & Community banner

1 - 20 of 2491 Posts

·
EZ GF w/Curves!
97'OBS/94'SVX LSi/00'OBS/01&#8
Joined
·
8,801 Posts
Discussion Starter #1 (Edited)
Dedicated to Dorothy Gaddis RIP. Nov 2, 2002 For showing me I can live however I want and to Fight for it. Also to never put up with anyones **** for it. I miss you Grandma! :'(
Check my other car's
01' Impreza L coupe http://www.rs25.com/forums/f145/t223340-another-acadia-green-l-coupe.html
00' Impreza OBS http://www.rs25.com/forums/f145/t144834-slow-gun-back-outback-obrs-ddr.html
96' Impreza L coupe http://www.rs25.com/forums/f145/t115228-seraphinwolfs-lacky-coupe.html#post1791634
94' SVX LSi http://www.rs25.com/forums/f145/t117188-seraphinwolfs-94-svx-heirloom.html#post1817757
So I talk about it alot cause... I'm taking forever to finish. Hopefully it's cause I'm building it right.

Photobucket album I'm staring to move project pics to good, bad, and ugly. Lilly AKA Project SixGun pictures by seraphinwolf - Photobucket



So this is Lilly and her set goal:
1997 Subaru Impreza Outback Sport.
_ Engine & Ehaust:
EZ30R H-6
Supertech Pistons 8.5:1
Supertech Valve Springs
Borg Warner S300SX 91/79 (S366)
Injector Dynamics 1000cc topfeed injectors
Deatsch Werks DW300 300LPH fuel pump
Twin Tial 38mm Vband EWG
Kinetic Motor Works custom Header, UP, and DP
GrimmSpeed 3port EBCS
Spearco Front mount with custom plumbing
GReddy Type R BOV
GR fitment Invidia Q300
Denso Oil-cooler

_ ECU:
Link G4 Extreme Standalone ECU with full DBW adapter
+ Parallel run
OEM 05' STi ECU

_ Powertrain:
04 STi 6speed( I chose the 04/05' for the increased rear bias)
SS braided clutch line and delay valve delete
STi shortthrow and linkage
07 STi hubs w/Brembos
Techna-Fit SS brake lines+ ABS delete
DBA 5000 front D/S rotors
DBA 4000 rear D/S rotors
V7 R180 rear diff
Kartboy Reardiff bushings
V8 Front axles
05' Rear axles
ACT Streetlite LWF
ACT XD pressure plate
ACT six puck(don't remember which)

_ Subframes and suspension:
05 STi sub frame
06 STi Crossmember
06 STi steeringrack
Bakemono-Imports Remote PS Reservoir kit
Whiteline Steeringrack bushings
Tie-Rod Ends from Whiteline RCA
Nagisa Auto control arms
Cusco GF struttower braces
Cobb 25mm front swaybar
Cobb 25mm rear swaybar
Cobb Upgrade Swaybar mount
KartBoy rear endlinks
Hotchkis Adjustable Latteral links
Bakemono-Imports Camberplates
Whiteline G4 STi coilovers
STi "pink" Trailing arms

_ Exterior:
Aero-Sim WRC Spec 4door widebody kit custom fit to GF chassis
Paint to be redone DGM lowers/Pearl or custom Aspen White upper. Possibly with black or DGM roof.
Custom CF hood.(yeah just wait for pics )
JDM roof racks
99-01 Clear headlights retrofitted E55 projector+ HIDs
Bakemono replica RA Roof Vent(custom Kevlar gold)
Bakemono S201 CF hood scoop
Bakemono WRC CF mirrors
V6 JDM 7lb Front bumper beam
V6 JDM 7lb Rear bumper beam

_ Interior:
07 Limited STi Dashboard swap
05 STi cluster
V4 STi front seats
Bakemono-Imports shifterboot
Custom RED carpet

More detail and pics updated spuraticly. Mostly read through and you'll see where things go array and come back together and what not. I keep chaging my mind. Lots of work from the start to get to where I want to be but for right now the car is garaged and half way stripped down for the swap and to get other work done as I can afford it.



-Gaddis



 

·
EZ GF w/Curves!
97'OBS/94'SVX LSi/00'OBS/01&#8
Joined
·
8,801 Posts
Discussion Starter #2 (Edited)
THIS IS MASSIVELY OUT OF DATE!!!Parts accuired: First one is obvious
05' EZ30R
Borge Warner SC366 twinscroll turbo
04' USDM STi 6 speed transmission
OEM Shortthrow 6mt shift linkage Part#C1010FE004
V7 JDM R180
V8 front axles
05' rear axles
07' STi 5x114.3 Hubs
05' STi Clutch Master Cylinder
05' STi Brake booster
05' STi brake and clutch pedals
GDB STi dash+beam
GDB STi steering collum
GDB STi rear subframe
GDB STi cross member
GDB STi steering column
GDB STi control arms
Bakemono-Imports ALK
COBB 25mm front sway bar
COBB 25mm adjustable rear swaybar
COBB upgraded rear swaybar mount*
EiteAWD Billet Aluminum Sway Bar Collar
Whiteline G4 coilovers
6 speed starter motor
97' 4EAT driveshift
Hotchkis endlinks
STi Brembo calipers powdercoated red
Goodrich SS brake lines*
DBA 5000 drilled and slotted two peice front rotors*
DBA 4000 drilled and slotted rear rotors
EZ30D(phase 1 3.0L from 01-04) engine mounts
KAR KB-025*trans mount bushings
KAR KB-066*rear subframe lockdown bolts
KAR KB-003-DIFF rear diff crossmember bushings
KAR KB-003-STI STi shifter bushing
KAR KB-003-REAR rear shifter bushing
00-01' headlights.
E55 projectors
07 STi centerconsol
6speed Yah Sensor
DCCD modual
DCCD switch
DCCD control switch.
Whiteline Steering rack bushing kit
ARP extended wheel studs
Bosch wideband o2 sensor
Cusco F&R strut tower brace
52MM Prosport AFR guage
52MM Prosport Oil Temp guage
JDM 7lb bumper beam
Denso Oil cooler
STi fender badges
V4 STi SEATS!!!!
Bakemono Imports CF S201 scoop!
JDM V3-4 turnsignals
Aeroism,LLC. Widebody rear bumpercover in Fiberglass
Bakemono-Imports UBBER CAMBER PLATES
GrimmSpeed 160degree Thermostat.
A'pexi adjustable FRP
GrimmSpeed AOS kit
GrimmSpeed Brake Booster Brace
CXRacing FMIC
 

·
EZ GF w/Curves!
97'OBS/94'SVX LSi/00'OBS/01&#8
Joined
·
8,801 Posts
Discussion Starter #3 (Edited)
Most current.

Was a little burried for a while but it's okay. Sat in the garage for a while.

Just before I started stripping her down.

The Plan



-Gaddis
 

·
EZ GF w/Curves!
97'OBS/94'SVX LSi/00'OBS/01&#8
Joined
·
8,801 Posts
Discussion Starter #4 (Edited)
VVVV This is esentually how my front end will look. Gonna work on Photoshopping it when i remember to load up PS on the laptop.

-Gaddis
 

·
EZ GF w/Curves!
97'OBS/94'SVX LSi/00'OBS/01&#8
Joined
·
8,801 Posts
Discussion Starter #6 (Edited)
Good luck with it, my H6 swap is getting good, you guys are gonna crap your pants when you find out how much ive spent so far, lol.
If it's under $15K then you still have a ways to go to catch up with the EZ swaps. My total when running how I like will be just shy of $20K but that does include all the work you see listed+cost of the car+other parts+etc. Good luck and make sure to post your findings in the resource thread.
-Gaddis
 

·
I ❤ BOOBIES
99 Coupe
Joined
·
16,993 Posts
If it's under $15K then you still have a ways to go to ketch up with the EZ swaps. My total when running how I like will be just shy of $20K but that does include all the work you see listed+cost of the car+other parts+etc. Good luck and make sure to post your findings in the resource thread.
-Gaddis
yup, youll see
 

·
EZ GF w/Curves!
97'OBS/94'SVX LSi/00'OBS/01&#8
Joined
·
8,801 Posts
Discussion Starter #9
Picked up a ton of parts to add into my piles.
52mm Prosport AFR and a 52mm Oil Temp
Blouch wideband o2
4300K 35W Osram D2S bulbs
E55 projectors in some 97 spec OEM light assemblies
^ Pulling these apart as we speak to redo them how I want
KYB GR2 fronts
KYB AGX rears
Eibach springs
04-05 STi Swaybar

On the way:
Powerslot Plus big rotor kit for the fronts

Talked to Dylan at DS1Motorsports and he's gonna build me my rear diff to go with my 5EAT. Also getting a big add-on to my end project costs.:drunk:
BREMBO'S! I may likely never be able to go under 18's between them and the Proslot kit if I put them together but I'll stop on a half a dime!
-Gaddis
 

·
EZ GF w/Curves!
97'OBS/94'SVX LSi/00'OBS/01&#8
Joined
·
8,801 Posts
Discussion Starter #12
Added link to folder with majority of related pics todate. Including some of the car well a little ricer.
-Gaddis
 

·
EZ GF w/Curves!
97'OBS/94'SVX LSi/00'OBS/01&#8
Joined
·
8,801 Posts
Discussion Starter #15
I wanna see your interior work d00d!
It'll certainly be interesting. My hopes are actually seeming to line up right that the Legacy parts are laying into the GD dash pretty well. Now my biggest set back..... Money :_sure: I could finish this up pretty quickly I'd bet if I had the funds to buy everything right now. I've been working on this in my head long before I even settled on the EZ30R and even more of it ever since I got the car in 03. I do lots of reading, planning and mental layouts.
-Gaddis
 

·
EZ GF w/Curves!
97'OBS/94'SVX LSi/00'OBS/01&#8
Joined
·
8,801 Posts
Discussion Starter #17
I'm guessing I should thank which ever MOD fixxed my spelling error in my title. THANK YOU WHOEVER! LOL I know this thing is "prod"ing along but it's not a prodject. (Bad pun!)
-Gaddis
 

·
EZ GF w/Curves!
97'OBS/94'SVX LSi/00'OBS/01&#8
Joined
·
8,801 Posts
Discussion Starter #18
Indefinate hold till I fix some mistakes

Project is on indefinate hold for a while. I have something going on in my life right now that I need to take care of. I may do some work witht he parts I have right now and will post uipdates if they come between now and when I return to the project as a "to be finished" goal. Wish me luck on my endevors as this is was more important to my self and the rest of my life than my car. Anyone reading just remember this. Never neglect or miss treat the ones you care about. Just never do it. :(
-Gaddis
 

·
EZ GF w/Curves!
97'OBS/94'SVX LSi/00'OBS/01&#8
Joined
·
8,801 Posts
Discussion Starter #19
Project moving again.

Not back on track as my plan was to keep buying parts as I had money which was basicly like my paycheck minus enough for bills. Things with the not-yet-back-to-future-Mrs. are going well... better. Spending on this will be cut by... A LOT for a while. I'll be applying to go back to college come January and I may need to find a job that I can work my schedual around school. Production plants don't works so well for that, but we'll see when i get a chance to talk to my boss about that and see what scheduals for classes look like. Should have a bunch of parts sold soon to put into the car fund and I just got my hands on an external oilcooler(not really needed yet but I can mock it up and got a good cheap price). I just need to clean through and cash in all the 5 cent cans I got in the garage as the money would be nice but also to get to the driver's side of the car. I'll likely talk to Dylan at DS1Motorsports about sending him payments for all the parts I've got accumulated in my want list through him and putting a chunk of change a side for a Hydra set up for my application. In the mean while I still gotta pull the old engine and trani out and get other things taken care of on the car to prep it to put the EZ30R and 5EAT in. I'm not dead and neither is my car. Just taking it slow and will see where I get from here. Maybe I'll get lucky and people will want to buy more parts. Maybe even the stock engine and trani and rear diff. Likely will try to sell the powertrain to SVX guys for swapping to 4.11FD over the 3.54FD.
-Gaddis
 

·
EZ GF w/Curves!
97'OBS/94'SVX LSi/00'OBS/01&#8
Joined
·
8,801 Posts
Discussion Starter #20
Okay so I got a couple parts lined up to actually be sold which means I'll have some money in the poject fund for paying for parts I got squirled away. Also told everyone for xmas and next month my Bday that I just want donations to the car fund. I picked up a external oilcooler from another member on here for CHEAP! couldn't pass up on the price. and once I see some money in the poject fund I'll be paying for a good bit of the parts I got held up at DS1Motorsports. Thanks Dylan! Brembos front and rear, STi subframes, STi rack and colum, A few other bits I'm sure I just can't think of them. Also might be getting the first part to start the widebody for the rear at least. Will be trying ot remember to get better pics of the engine and trani and the mess that is my side of the garage. Temped to push the car out and turn it around before we get any accumulation of snow to work on the rear 1/4's over the winter. but that may be too much work at the momet.
-Gaddis
 
1 - 20 of 2491 Posts
Top