Subaru Impreza GC8 & RS Forum & Community banner
Status
Not open for further replies.
1 - 9 of 9 Posts

·
Registered
2002 WRX wagon "DOLORES"
Joined
·
118 Posts
Discussion Starter · #1 ·
Ive built this car for the past 4.5 years. ive loved it and taken very good care of it but i have a gut feeling its time to move on. Time to walk away from the honda world. Just a little history on the car. its an Ohio car, clean title. has been stored winters since ive owned it. i am the 3rd owner but have built it primarily from the ground up for autox and HPDE and ive done both and this car is amazing. Im asking $6500.00 and that includes a few things not on the car yet(listed below).. I WILL NOT PART THE CAR OUT!!












Engine:
B20Z2 35k miles. OBD1
+including+ JDM P8R Ported & Polished and Valve work. Done at PortFlow in Cali. 0 miles, as well as OEM head gasket, thermal intake gasket.
JDM ITR trans(8k miles) completely rebuilt in TX with new synchros
Exedy organic clutch
Exedy 9ld flywheel
LS intake manifold
P75 ecu
5zigen header
Omnipower test pipe
Buddy Club spec II (discontinued)
+including+ NIB Spoon like can muffler(incase the spec II is to loud)
MemoryFab carbon intake
magnecor wires
NGK plugs
Fluidyne full sized 2" DC2 radiator
12" slim fan
ES motor mount inserts.
Mashall FPG
Odyessy PC 680 battery(12 months old)
Skunk 2 battery Tie down
removed washer fluid bottle, new alt belt, new ignition switch and coil

:Foot Work:
Omni Power ITR sport coilovers (12k/10k)
ITR lower control arms
GSR brake conversion all 4 corners
Rotora Slotted Rotors hawk hp+(front) / duralast rotors and axxis ultimate pads(rear)
Goodrich SS lines
Motul RBF 600 fluid
Password 3pt front(painted white)
Custom Cusco rear bar
EG6 front 22mm sway bar
ITR 22mm rear sway w/ new bushings
Beaks Kit
Carbing tie bar
C-pillar bar
15 x 6.5" Sprint Hart CPs (red) with 205/50/15 hankook R-S2s
15 x 7" Rota Slipstreams (camo green!) 205/50/15 Falken Azenis(old style w/ alotta life)
Skunk2 lug nuts
race spec alignment(ask if needed)

:exterior:
OEM front lip(camo tape will be removed)
JDM stanley corners
Carbon Duckbill
composites fab one off Team Sloth canards
ABUNAI Racing vented carbon hood 1 of 3 made(needs to re clear-coated)
cheap hood pins, no latch
Circuit Hero Front and Rear Tow Hooks & tow stickers :p (sponsered car)
MemoryFab Carbon EG Intake Duct(only one in the US)
aftermarket pop-up sun roof

:interior:
gutted rear sections no carpet/tar/rear panels
MemoryFab BLACK kevlar S68 seat w/ super low rails(S58 shown in photo)
NRG recaro type seat. needs rails.
Kirk Racing 4pt roll bar(painted green)
Takata harness(expired 2007)
sparco 215 deep dish suede rally wheel
nar-spec quick release
momo hub
JDM Si-R II cluster
Custom camo door panels
SRR magenta colored pedal covers
EK9 CTR shift boot
circuit hero shift knob and extention
JVC head unit
will include driver side seat belt, OEM seats.

the only issue currently is that is typical honda EG rust.. its not horrible..mostly rust bubbles. wipers have been taken off.. wiring needs checked. there is power nothing..it is a DX model. i have some extra OEM parts if wanted. if you have any questions please PM me or email me at:
[email protected]
thank you
 
1 - 9 of 9 Posts
Status
Not open for further replies.
Top