Neme-WAGUN ej2.0g - Page 16 - Subaru Impreza GC8 & RS Forum & Community: RS25.com
 
Private Support i-Trader Ratings Become a Vendor Rules for VendorsModsUsers Contact
Subaru Impreza GC8 & RS Forum & Community: RS25.com
gc8 RSS GC8 Facebook Subaru GC8 Twitter Subaru YouTube Channel Subaru Sticker
 
Login below or Register Now
Register Mark Forums Read FAQ Advertise
Go Back   Subaru Impreza GC8 & RS Forum & Community: RS25.com > >
Neme-WAGUN ej2.0g
Reply
 
Thread Tools Display Modes
Old 10-19-2018, 02:33 PM   #151
NemeGuero
3.3L
 
Car: 95 impreza wagon
Join Date: Dec 2012
Location: Seattle
Trader Rating: (11)
Posts: 707
Default



1.5 way
Says it needs the VLSD housing so I'll probably have some fun figuring out it won't fit in my open diff and then trying to figure out what axles I need and that none of the 12 i have in my garage will fit. geeze I sound like a grumpy old man.

I AM EXCITE

also bought a hatch that had originally had spoilers on it from factory so I wouldn't need to drill holes. BUT.. glass didn't make it. so now I get to decide if I spend way too much money replacing the glass or using the "new" hatch as a template to just drill my old one out anyway.

bonus is that it came with the harness that the previous owner had hacked to pieces.



I got the tank bolt yesterday from the dealer and hopefully my fuel vent hose comes today. Then I can complete the fuel tank fiasco and move on to some more fun.

Last edited by NemeGuero; 10-19-2018 at 02:37 PM..
NemeGuero is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 10-20-2018, 05:12 PM   #152
NemeGuero
3.3L
 
Car: 95 impreza wagon
Join Date: Dec 2012
Location: Seattle
Trader Rating: (11)
Posts: 707
Default

measure twice.. cut-fuck. Guess I should have measured better than the old extended thumb and first finger, twice, approximation.

I suck


got the filler neck cleaned and re-installed to at least feel like I accomplished something today



then I started cracking open the diff for the kaaz install
and like I figured, wrong diff or I have the wrong one it installs into.
final drive gear wont even go on and no way in hell this fits





the stagnation continues
NemeGuero is offline   Reply With Quote
Old 10-20-2018, 05:35 PM   #153
bue car
#32
 
bue car's Avatar
 
Fav Mod: Which car?
Join Date: Jun 2008
Location: Torrance, CA
Trader Rating: (173)
Posts: 11,746
Default

Is that for a transmission?


__________________
Save RS25! Say no to XenForo
bue car is offline   Reply With Quote
Old 10-20-2018, 05:37 PM   #154
NemeGuero
3.3L
 
Car: 95 impreza wagon
Join Date: Dec 2012
Location: Seattle
Trader Rating: (11)
Posts: 707
Default

I think its for the r180.
NemeGuero is offline   Reply With Quote
Old 10-20-2018, 05:57 PM   #155
bue car
#32
 
bue car's Avatar
 
Fav Mod: Which car?
Join Date: Jun 2008
Location: Torrance, CA
Trader Rating: (173)
Posts: 11,746
Default

The holidays are coming up. Santa could sent it to me...
__________________
Save RS25! Say no to XenForo
bue car is offline   Reply With Quote
Old 10-20-2018, 08:40 PM   #156
scruff3333
Premium Member
 
scruff3333's Avatar
 
Fav Mod: broken motor
Join Date: Jun 2014
Location: wetside washington
Trader Rating: (10)
Posts: 825
Default

Quote:
Originally Posted by bue car View Post
the holidays are coming up. Santa could sent it to me...
🤣
__________________
Nerds get to go to the moon
scruff3333 is offline   Reply With Quote
Old 11-11-2018, 08:29 PM   #157
scruff3333
Premium Member
 
scruff3333's Avatar
 
Fav Mod: broken motor
Join Date: Jun 2014
Location: wetside washington
Trader Rating: (10)
Posts: 825
Default

What's happenin?

Where ya been?
__________________
Nerds get to go to the moon
scruff3333 is offline   Reply With Quote
Old 11-12-2018, 07:58 AM   #158
AlexJakubiak
1.8L
 
Car: 2001 Subaru Impreza OBS
Fav Mod: NA/T
Join Date: May 2018
Location: Wisconsin
Trader Rating: (0)
Posts: 29
Default

Quote:
Originally Posted by NemeGuero View Post
the amassing continues


are there plugs that fill the headlight sprayer holes?

and finally got the rear coilovers on
What exhaust tip is this? need.
AlexJakubiak is offline   Reply With Quote
Old 11-12-2018, 08:18 AM   #159
NemeGuero
3.3L
 
Car: 95 impreza wagon
Join Date: Dec 2012
Location: Seattle
Trader Rating: (11)
Posts: 707
Default

Finally got the stupid rear brake lines. I went to go put the old ones on and they had a little corrosion on them. I wire wheeled them but decided at $30 a piece to just get new ones, and then I ordered all new clips for front and rear so most of my absence was waiting for those fucking parts to arrive.

But also, its cold outside and its hard to find motivation to be in the garage.

New lines and clips in the rear:


He wants to help




New clips and NON ABS lines in the front. Can't fucking get the triangle one on the passenger side at the top.


gas tank finally up now that the lines are in place with a long enough vent hose.


rear subframe quickly follows suit


I feel like I should have had these powder coated to match.. :/


DONT FORGET TO CONNECT THESE


tank protectors


RIGHT diff!


ring gear on


where I grindeded, i actually had to grind a little on the flat between the nubs for the bolt head to pass through.



Kaaz'd up!




the muffler is some ebay crap. DTM 3" bent tip something something.. I'll see if I can find the link.
NemeGuero is offline   Reply With Quote
Old 11-12-2018, 08:19 AM   #160
NemeGuero
3.3L
 
Car: 95 impreza wagon
Join Date: Dec 2012
Location: Seattle
Trader Rating: (11)
Posts: 707
Default

Quote:
Originally Posted by AlexJakubiak View Post
What exhaust tip is this? need.
3" Outlet Dtm Dual Tilt Slant Tip Muffler Exhaust w/ 2.5" Inlet | eBay

you gotta dig a bit harder to find the 3" inlet one with the burnt tips but I don't remember where.
NemeGuero is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -7. The time now is 06:01 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright © 2019 VerticalScope Inc.
Designed & Powered by Domain Architect