2001 Impreza L | WRX swapped | Rust repairs and weight reduction! - Page 95 - Subaru Impreza GC8 & RS Forum & Community: RS25.com
 
Private Support i-Trader Ratings Become a Vendor Rules for VendorsModsUsers Contact
Subaru Impreza GC8 & RS Forum & Community: RS25.com
gc8 RSS GC8 Facebook Subaru GC8 Twitter Subaru YouTube Channel Subaru Sticker
 
Login below or Register Now
Register Mark Forums Read FAQ Advertise
Go Back   Subaru Impreza GC8 & RS Forum & Community: RS25.com > >
2001 Impreza L | WRX swapped | Rust repairs and weight reduction!
Reply
 
Thread Tools Display Modes
Old 05-10-2019, 05:36 AM   #941
RavensFan77
Premium Member
 
Car: 2001 Subaru Impreza L coupe
Fav Mod: Ej205
Join Date: May 2012
Location: PA
Trader Rating: (1)
Posts: 711
Default

Clutch maintenance:

Clutch has been feeling worse and worse lately. Vibrations in the pedal, heavy pedal, squeak/creaking/dragging while pressing clutch pedal. Multiple issues....

Vibration issue was easy.....lost the little helper return spring again. Donít know why it keeps breaking or falling off. Doesnít make much of a difference, but the fork does rattle around without it.

A while ago I found a similar tension and length spring at the hardware store, and have been using it on my sedan for a while. Put one on this car and I think itíll last longer than the oem one. Works really well.



Next I replaced the cable. It wasnít broken, but had seen better days. All the dust boots were torn, and the crimped end by the pedal was cracked and falling apart.

Had a new oem cable for years now, Incase mine broke.








So new cable felt better, but squeak/creaking was still there. Definitely from inside the bellhousing. Only thing to try without removing the engine/trans was to grease the pivot point. Was able to reach down the fork and wipe some grease on the pivot.

Wow. Clutch is buttery smooth now. Pedal is lighter, and no noise or dragging. Felt completely different to drive. Iím sure itís not a permanent solution, but should buy some time. Probably do it again in like a month.

Best picture I could get. I didnít leave the big glop like that. Wiped it around more and cleaned out some of the dust build-up.



New cable needs lots of adjusting. At first it was too short, and I couldnít even fit both jam nuts on the cable. Now after pressing the clutch lots of times, adjusting it 15+ times, and a drive, itís getting closer to where it should be.

Good thing itís really easy to adjust.




Also......

Replaced all my catch can lines. I lazily used heater core hose temporarily and never went back to replace it. Heater hose breaks down after a while. Used low pressure fuel line (30r7) which good for fuel/oils/pcv and should last a while. 1/2Ē for valve covers and 3/4Ē for crankcase.

Dual eBay catch can setup ($30 total) is still working fantastic. Canít imagine paying for an AOS. Still plan on making a big aluminum catch can to mount behind the driver side headlight one day....but this works great for now.





And a random front picture

RavensFan77 is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 05-10-2019, 09:10 AM   #942
George.of.the.Jungle
Baby❤Daddy
 
George.of.the.Jungle's Avatar
 
Fav Mod: BOOOOOOST!!
Join Date: Aug 2002
Location: Charleston, SC
Trader Rating: (75)
Posts: 27,831
Default

looking good as always.
__________________
friends dont let friends put stupid GD scoops on their first gen car.
George.of.the.Jungle is offline   Reply With Quote
Old 05-10-2019, 03:12 PM   #943
FryphaX
Premium Member
 
FryphaX's Avatar
 
Fav Mod: Registration!
Join Date: Nov 2012
Location: Home - U.P. of Michigan Work takes me everywhere.
Trader Rating: (4)
Posts: 2,541
Default

How is your engine bay so clean! Jealous.
__________________
2001 SRP Coupe 8300RPM SOHC 257, 71 HTA, DCCD RA Drivetrain and ms3-Pro
FryphaX is offline   Reply With Quote
Old 05-17-2019, 04:26 AM   #944
RavensFan77
Premium Member
 
Car: 2001 Subaru Impreza L coupe
Fav Mod: Ej205
Join Date: May 2012
Location: PA
Trader Rating: (1)
Posts: 711
Default

Quote:
Originally Posted by FryphaX View Post
How is your engine bay so clean! Jealous.

Something has to look presentable.....the rest of the car is looking pretty rough these days
RavensFan77 is offline   Reply With Quote
Old 05-17-2019, 04:26 AM   #945
RavensFan77
Premium Member
 
Car: 2001 Subaru Impreza L coupe
Fav Mod: Ej205
Join Date: May 2012
Location: PA
Trader Rating: (1)
Posts: 711
Default 2001 Impreza L | WRX swapped | Rust repairs and weight reduction!

Trying to get back into things.....havenít really used my TIG much cause I needed a way to cut tubing nice and square, quickly, with angles if needed. Bandsaw was out of the budget.....so a cheap miter saw was the best way I could come up with.

Quick clean up of the edges and it fits up nice for welding.....better than a sawzall/hacksaw anyway.....

Nicer downpipe and fmic piping coming soon! Gonna chop up some scrap pieces this weekend and start messing around.






Also, random GoPro video from the other week cause I was bored. Never really taken any videos of the car before.

RavensFan77 is offline   Reply With Quote
Old 05-17-2019, 04:36 AM   #946
FryphaX
Premium Member
 
FryphaX's Avatar
 
Fav Mod: Registration!
Join Date: Nov 2012
Location: Home - U.P. of Michigan Work takes me everywhere.
Trader Rating: (4)
Posts: 2,541
Default

Quote:
Originally Posted by RavensFan77 View Post
Something has to look presentable.....the rest of the car is looking pretty rough these days
Touchť. I thought mine was going to be super neat until I started actually plumbing everything up. Makes me wish I went rotated now!
__________________
2001 SRP Coupe 8300RPM SOHC 257, 71 HTA, DCCD RA Drivetrain and ms3-Pro
FryphaX is offline   Reply With Quote
Old 05-17-2019, 05:00 AM   #947
Ted
2.5L RS-T
 
Join Date: Sep 2011
Location: The Shire
Trader Rating: (3)
Posts: 5,137
Default

When you are doing aluminum in the chop saw it helps to run a bar of soap along the disc prior to cutting. It slows down the build up on the disc.

Sent from my SM-N920V using Tapatalk
__________________
A three syllable word for thoughts too big for small minds
Ted is offline   Reply With Quote
Old 05-17-2019, 05:10 AM   #948
TerryJr
Experimenter
 
TerryJr's Avatar
 
Fav Mod: AAA Premier
Join Date: Jun 2009
Location: Pittsburgh
Trader Rating: (0)
Posts: 3,739
Default

Quote:
Originally Posted by Ted View Post
When you are doing aluminum in the chop saw it helps to run a bar of soap along the disc prior to cutting. It slows down the build up on the disc.

Sent from my SM-N920V using Tapatalk
he speaks the truth, a little soap on abrasive discs cutting/grinding aluminum works magic
__________________
Why should we be paying to keep guy's like Chris Watts and Michael Glance alive?
TerryJr is online now   Reply With Quote
Old 05-17-2019, 10:14 AM   #949
RavensFan77
Premium Member
 
Car: 2001 Subaru Impreza L coupe
Fav Mod: Ej205
Join Date: May 2012
Location: PA
Trader Rating: (1)
Posts: 711
Default

Quote:
Originally Posted by FryphaX View Post
Makes me wish I went rotated now!

Never too late to change

Quote:
Originally Posted by Ted View Post
When you are doing aluminum in the chop saw it helps to run a bar of soap along the disc prior to cutting. It slows down the build up on the disc.

Sent from my SM-N920V using Tapatalk


Quote:
Originally Posted by TerryJr View Post
he speaks the truth, a little soap on abrasive discs cutting/grinding aluminum works magic

Sweeeet, gonna try that out. I only did the one cut, but noticed the aluminum buildup on the disc already
RavensFan77 is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -7. The time now is 12:09 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright © 2019 VerticalScope Inc.
Designed & Powered by Domain Architect